Multi-Tech ISIHI-2S Especificações Página 85
- Página / 188
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
MultiModem ISI Hybrid Series, ISIHI-2S/2U 85
Chapter 4—MODEM AT Commands, S-Registers, Result Codes
S8 Pause Time for Comma
Unit: 1 second
Range: 065 (North America), 4255 (International), 47 (UK)
Default: 2 (North America), 4 (International and UK)
Determines the length of pause caused by a comma character in a dialing command.
Default setting is two seconds for North American model and four seconds for
international and UK models. S8 can be set for up to 65 seconds. S8 also defines the
length of time the modem waits before retrying a call after it detects a busy signal. Some
computer systems need more than two seconds to reset. If this is the case, increase the
value of S8.
S10 Carrier Loss Disconnect Delay Time
Unit: 100 ms
Range: 1254
Default: 20
Defines the length of time, in milliseconds, that the modem waits after a loss of carrier
signal before the it disconnects. The default setting is 2000 ms (20 units of 100 ms each).
Maximum delay is 25400 milliseconds, or 25.4 seconds (decimal 254).
S11 Tone Dialing Spacing and Duration
Unit: 1 ms
Range: 50 - 150 (US) or 80255 (Canada, UK, International)
Default: 95 (US) or 80 (Canada, UK, International)
Sets the speed of tone dialing (spacing and tone duration times). The default value is 95
units for domestic models and 80 units for Canadian and International models, where
each unit is one ms. In other words, for domestic modems, each tone is sustained for 95
ms followed by a 95 ms pause. The minimum S11 value allowed is 50 ms (50 units). The
maximum S11 value is 150 ms (150 units).
S28 Enable / Disable V.34 Modulation
Unit: decimal
Range: 0, 1255
Default:1 (enabled)
Enables or disables V.34 modulation. Setting S28 to zero (0) disables V.34 modulation.
Any other setting (1-255) enables V.34 modulation.
S35 Data Calling Tone
Unit: decimal
Range: 01
Default: 0 (disabled)
Enables or disables the V.25 data calling tone, which allows remote data, fax and voice
discrimination. Setting S35 to zero (0) disables V.25 data calling tone; setting S35 to 1
enables data calling tone. The default setting is 1.
- MultiModemISI Hybrid Series 1
- Model ISIHI-2S/2U 1
- Contents 3
- Introduction 1 5
- Modem Description/Features 8
- Manual Organization 10
- Chapter 1—Introduction 11
- Technical Specifications 12
- Terminal Adapter 14
- Hardware Installation 2 15
- Before You Start 17
- Installing the ISIHI-2S/2U 18
- LED Indicators 20
- P LED Indicator 21
- D LED Indicator 21
- terminal adapters: 27
- To install 29
- Removing the Driver 32
- IRQ for the card. Click OK 36
- Setting 37
- Optional Settings 48
- ISDN TA Configuration Utility 49
- AT Commands 54
- Removing the Driver (Novell) 56
- Multi_Setup Utility 61
- Administration Utility 64
- Linux Driver Installation 65
- Miscellaneous: 66
- AT Commands, S-Registers 67
- Modem AT Commands 68
- Topic Command Description 70
- Dialing Commands 71
- Dial Modifier Commands 71
- Phone Number Memory Commands 72
- Online Connection Commands 75
- RS-232 Interface Commands 77
- Immediate Action Commands 79
- Flow Control Commands 80
- Escape Sequences 82
- Modem S-Registers 83
- Modem Result Codes 89
- TERMINAL ADAPTER 91
- Terminal Adapter AT Commands 92
- Command Implementation 94
- Switch Configuration Commands 94
- NTER. The dialing string can 102
- Data Call Commands 104
- Terminal Adapter S-Registers 105
- NTER, the escape 107
- Terminal Adapter Result Codes 108
- Making a Call 109
- Modes of Operation 109
- Answering a Call 110
- Hanging Up 110
- Troubleshooting 6 111
- Troubleshooting 112
- Service, Warranty, and 117
- Technical Support/BBS 117
- Introduction 118
- Limited Warranty 118
- Online Warranty Registration 118
- Techical Support 119
- The Multi-Tech BBS 121
- About CompuServe 123
- About the Internet 123
- Appendix 125
- Address Switch Settings 127
- Appendix C: Pin Assignments 129
- Quick Setup Factory Profiles 133
- Quick Setup Example 133
- Loop Qualification 137
- Bearer Service 138
- How To Use AT Commands 162
- Appendix N: Result Codes (TA) 169
- FCC Part 68 Telecom 170
- Industry Canada 171
- FCC Fax Warning 171
- Canadian Limitations Notice 172
- Glossary 173
Manuais e produtos relacionados com Redes Multi-Tech ISIHI-2S
Redes Multi-Tech FR3100 Manual de Serviço
(71 páginas)
(71 páginas)
Redes Multi-Tech ISIHI-2S Manual do Proprietário
(64 páginas)
(64 páginas)
Redes Multi-Tech FR3100 Manual do Utilizador
(20 páginas)
(20 páginas)
Redes Multi-Tech MT128ISA-UV Manual do Proprietário
(117 páginas)
(117 páginas)
Norac UC4+JD9-4B podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Sprzęt ogrodniczy Norac UC4+JD9-4B.
Dostarczamy 1 pdf podręczników Norac UC4+JD9-4B do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Norac UC4+JD9-4B Instrukcja Użytkownika (13 strony)
Marka: Norac | Kategoria: Gardening equipment | Rozmiar: 0.63 MB |
Więcej produktów i instrukcji dla Sprzęt ogrodniczy Norac
| Modele | Rodzaj dokumentu |
|---|---|
| UC4+BC+OM1 |
Instrukcja Użytkownika
NORAC UC4+BC+OM1 User Manual,
26 strony
|
| UC4+BC+MC1 |
Instrukcja Użytkownika
NORAC UC4+BC+MC1 User Manual [fr] [de] ,
36 strony
|
| UC4+BC+MC2 |
Instrukcja Użytkownika
NORAC UC4+BC+MC2 User Manual [en] [de] ,
37 strony
|
| UC4+BC+NT3 |
Instrukcja Użytkownika
NORAC UC4+BC+NT3 User Manual,
36 strony
|
| UC4+BC+NT4 |
Instrukcja Użytkownika
NORAC UC4+BC+NT4 User Manual,
37 strony
|
| UC4+BC+RB1 |
Instrukcja Użytkownika
NORAC UC4+BC+RB1 User Manual [fr] [de] [it] ,
32 strony
|
| UC4+BC+RG6 |
Instrukcja Użytkownika
NORAC UC4+BC+RG6 User Manual,
39 strony
|
| UC4+BC+RG4 |
Instrukcja Użytkownika
NORAC UC4+BC+RG4 User Manual,
40 strony
|
| UC4+BC+RG7 |
Instrukcja Użytkownika
NORAC UC4+BC+RG7 User Manual,
35 strony
|
| UC4+BC+SC1 |
Instrukcja Użytkownika
NORAC UC4+BC+SC1 User Manual,
35 strony
|
| UC4+BC+SC2 |
Instrukcja Użytkownika
NORAC UC4+BC+SC2 User Manual,
36 strony
|
| UC4+BC+SC4 |
Instrukcja Użytkownika
NORAC UC4+BC+SC4 User Manual,
27 strony
|
| UC4+BC+TA1 |
Instrukcja Użytkownika
NORAC UC4+BC+TA1 User Manual,
37 strony
|
| UC4+BC+WR1 |
Instrukcja Użytkownika
NORAC UC4+BC+WR1 User Manual [pl] [cs] [de] ,
32 strony
|
| UC4+BC+WR2 |
Instrukcja Użytkownika
NORAC UC4+BC+WR2 User Manual,
31 strony
|
| UC4+BC+FT1 |
Instrukcja Użytkownika
NORAC UC4+BC+FT1 User Manual,
30 strony
|
| UC4+BC+FT2 |
Instrukcja Użytkownika
NORAC UC4+BC+FT2 User Manual,
28 strony
|
| UC4+BC+FT2A |
Instrukcja Użytkownika
NORAC UC4+BC+FT2A User Manual [es] [en] [de] ,
29 strony
|
| UC4+BC+HD8A |
Instrukcja Użytkownika
NORAC UC4+BC+HD8A User Manual,
34 strony
|
| UC4+BC+HG |
Instrukcja Użytkownika
NORAC UC4+BC+HG User Manual,
28 strony
|
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais